Difference between revisions of "ECE 110/Fall 2022"

From PrattWiki
Jump to navigation Jump to search
(Test Reviews)
(Test Reviews)
 
(One intermediate revision by the same user not shown)
Line 27: Line 27:
 
=== Test Reviews ===  
 
=== Test Reviews ===  
 
* [[ECE_110/Fall_2022/Test_1|Test 1]]
 
* [[ECE_110/Fall_2022/Test_1|Test 1]]
<!--
 
 
* [[ECE_110/Fall_2022/Test_2|Test 2]]
 
* [[ECE_110/Fall_2022/Test_2|Test 2]]
* Final: Test 1, Test 2, Filter circuits, and Operational Amplifiers:
+
* Final: Test 1, Test 2, Operational Amplifiers, Binary / Digital Logic:
 
** Know the Ideal Op-Amp assumptions (infinite internal input impedance, zero internal output impedance, and infinite internal voltage gain),  
 
** Know the Ideal Op-Amp assumptions (infinite internal input impedance, zero internal output impedance, and infinite internal voltage gain),  
 
** Know the implications when an Ideal Op-Amp is put into a circuit where the is feedback from the output to the inverting terminal (no voltage drop across the input terminals and no current into/out of the input terminals).
 
** Know the implications when an Ideal Op-Amp is put into a circuit where the is feedback from the output to the inverting terminal (no voltage drop across the input terminals and no current into/out of the input terminals).
Line 35: Line 34:
 
** Understand that the only time you would write KCL at the output terminal of an Op-Amp is if you are trying to calculate the current coming out of the Op-Amp (which, incidentally, is general nonzero).
 
** Understand that the only time you would write KCL at the output terminal of an Op-Amp is if you are trying to calculate the current coming out of the Op-Amp (which, incidentally, is general nonzero).
 
** Understand that you cannot use KCL at ground if there is an Op-Amp circuit because we are not explicitly including several connections from ground that connect to the Op-Amp.  See Figure 6.2-2 so see two additional connections to ground which we generally do not include while analyzing Op-Amp circuits but which would be required for using KCL at ground.
 
** Understand that you cannot use KCL at ground if there is an Op-Amp circuit because we are not explicitly including several connections from ground that connect to the Op-Amp.  See Figure 6.2-2 so see two additional connections to ground which we generally do not include while analyzing Op-Amp circuits but which would be required for using KCL at ground.
** Example problems from the [http://classes.pratt.duke.edu/Gustafson/OmnibusTestBank.html Test Bank]:
+
** Example op-amp problems from the [http://classes.pratt.duke.edu/Gustafson/OmnibusTestBank.html Test Bank]:
 
*** EE 61 Spring 2001 Test 2 Problem 4
 
*** EE 61 Spring 2001 Test 2 Problem 4
 
*** EE 61 Fall 2001 Test 2 Problem 3
 
*** EE 61 Fall 2001 Test 2 Problem 3

Latest revision as of 17:10, 13 December 2022

ECE 110 is a required course for all students planning to earn a major in Electrical and Computer Engineering or Biomedical Engineering at Duke University. It may also be taken to satisfy the cross-disciplinary requirement for the Civil and Environmental Engineering degree. This page is meant to provide answers to general questions about the course, not necessarily specific questions about content. There is also a Category:ECE 110 that will list all pages relevant to ECE 110. Note at the bottom of this page that it is a member of that category. This is the page for Fall, 2022.

Lab Supplemental Pages

Lab Errata

None yet!


Support Pages for Lecture Section 1 (Dr. G) for Fall 2022

Lecture / Homework Support Pages

Test Reviews

  • Test 1
  • Test 2
  • Final: Test 1, Test 2, Operational Amplifiers, Binary / Digital Logic:
    • Know the Ideal Op-Amp assumptions (infinite internal input impedance, zero internal output impedance, and infinite internal voltage gain),
    • Know the implications when an Ideal Op-Amp is put into a circuit where the is feedback from the output to the inverting terminal (no voltage drop across the input terminals and no current into/out of the input terminals).
    • Know how to analyze Op-Amp circuits, generally by using KCL at the input terminals of the Op-Amp.
    • Understand that the only time you would write KCL at the output terminal of an Op-Amp is if you are trying to calculate the current coming out of the Op-Amp (which, incidentally, is general nonzero).
    • Understand that you cannot use KCL at ground if there is an Op-Amp circuit because we are not explicitly including several connections from ground that connect to the Op-Amp. See Figure 6.2-2 so see two additional connections to ground which we generally do not include while analyzing Op-Amp circuits but which would be required for using KCL at ground.
    • Example op-amp problems from the Test Bank:
      • EE 61 Spring 2001 Test 2 Problem 4
      • EE 61 Fall 2001 Test 2 Problem 3
      • ECE 110 Fall 2014 Test 2 Problem 5
      • EGR 119(224) Spring 2009 Test 2 Problem 4
      • EGR 224 Spring 2013 Test 2 Problem 4 (1)
      • EGR 224 Spring 2014 Test 2 Problem 4 (2) if the Z were all R instead
      • EGR 224 Spring 2016 Test 2 Problem 4

-->

F.A.Q.

  • None as yet

Questions

Post your questions by editing the discussion page of this article. Edit the page, then scroll to the bottom and add a question by putting in the characters *{{Q}}, followed by your question and finally your signature (with four tildes, i.e. ~~~~). Using the {{Q}} will automatically put the page in the category of pages with questions - other editors hoping to help out can then go to that category page to see where the questions are. See the page for Template:Q for details and examples.

External Links

Note: there will be different homework assignments, and possibly different policies among the different sections -- be sure to follow the appropriate guidance for the appropriate section!

References