EGR 224/Concept List/S24

The notes below are not meant to be comprehensive but rather to capture the general topics of covered during lectures in EGR 224 for Spring 2024. These notes are in no way a replacement for actively attending class.

Lecture 1 - 1/10 - Course Introduction, Nomenclature

• Circuit terms (Element, Circuit, Path, Branch and Essential Branch, Node and Essential Node, Loop and Mesh).
• Accounting:
  • # of Elements * 2 = total number of voltages and currents that need to be found using brute force method
  • # of Essential Branches = number of possibly-different currents that can be measured
  • # of Meshes = number of independent currents in the circuit (or generally Elements - Nodes + 1 for planar and non-planar circuits)
  • # of Nodes - 1 = number of independent voltage drops in the circuit
• Electrical quantities (charge, current, voltage, power)

Lecture 2 - 1/12 - Electrical Quantities

• Passive Sign Convention and Active Sign Convention and relation to calculating power absorbed and/or power delivered.
• Power conservation
• Kirchhoff's Laws
  • Number of independent KCL equations = nodes-1
  • Number of independent KVL equations = meshes
• Example of how to find $$i$$, $$v$$, and $$p_{\mathrm{abs}}$$ using conservation equations and how to check using extra conservation equations
• $$i$$-$$v$$ relationships of various elements (ideal independent voltage source, ideal independent current source, short circuit, open circuit, switch)
• Resistor symbol (and spring symbol)

Lecture 3 - 1/19 - Equivalents

• Resistance as $$R=\frac{\rho L}{A}$$
• $$i$$-$$v$$ relationship for resistors; resistance [$$\Omega$$] and conductance $$G=1/R$$ $$[S]$$
• $$i$$-$$v$$ for dependent (controlled) sources (VCVS, VCCS, CCVS, CCCS)
• Combining voltage sources in series; ability to move series items and put together
• Combining current sources in parallel; ability to move parallel items and put together
• Equivalent resistances
  • series and parallel
  • Examples/Req

Lecture 4 - 1/22 - Brute Force Method; Delta-Wye; Voltage Division Part 1

• Brute Force method
• Delta-Wye equivalencies (mainly refer to book)
• Voltage Division

Lecture 5 - 1/26 - Voltage Division Part 2, Current Division, and Node Voltage Division Part 1

• Voltage Re-Division
• Current Division and Re-Division
• Basics of NVM

Lecture 6 - 1/29 - Node Voltage Method

• NVM
  • Examples on Canvas
  • Labels:
    • Very Lazy: label ground, then make every other node a new unknown. Voltage sources, voltage measurements, and current measurements will provide additional equations.
    • Lazy: label ground, then label any node connected to ground if it has a voltage source or voltage measurement. Make every other node a new unknown. Voltage sources not connected to ground, voltage measurements not connected to ground, and current measurements will provide additional equations.
    • Smart: label ground; once a node gets labeled, if there is a voltage source or a voltage measurement anchored at that node, use the source or measurement to label the other node it is attached to. Current measurements will provide additional equations.
    • Really Smart: same as smart, only also use voltage drops across resistors with current measurements to relate node voltages.

Lecture 7 - 2/2 - Current Methods

• Examples on Canvas
• BCM
  • Labels:
    • Label each (essential) branch current, using as few unknowns as possible by incorporating current source and current measurement labels
• MCM
  • Labels:
    • Label each mesh current, understanding that current sources, current measurements, and voltage measurements will require additional equations.

Lecture 8 - 2/5 - Linearity and Superposition

• Definition of a linear system
• Examples of nonlinear systems and linear systems
  • Nonlinear system examples (additive constants, powers other than 1, trig):

$$\begin{align*} y(t)&=x(t)+1\\ y(t)&=(x(t))^n, n\neq 1\\ y(t)&=\cos(x(t)) \end{align*} $$

• Linear system examples (multiplicative constants, derivatives, integrals):

$$\begin{align*} y(t)&=ax(t)\\ y(t)&=\frac{d^nx(t)}{dt^n}\\ y(t)&=\int x(\tau)~d\tau \end{align*} $$

• Superposition
  • Redraw the circuit as many times as needed to focus on each independent source individually
  • Use combinations of Phm's Law, Voltaeg Division, and Current Division, rather than setting up and solving multiple equations
  • If there are dependent sources, you must keep them activated and solve for measurements each time - this likely means that superposition may not actually make solving things easier.

Lecture 9 - 2/9- Thévenin and Norton Equivalent Circuits

• Thévenin and Norton Equivalents
• Circuits with independent sources, dependent sources, and resistances can be reduced to a single source and resistance from the perspective of any two nodes
• Equivalents are electrically indistinguishable from one another
• Several ways to solve:
  • If there are only independent sources, turn independent sources off and find $$R_{eq}$$ between terminals of interest to get $$R_{T}$$. Then find $$v_{oc}=v_{T}$$ and recall that $$v_T=R_Ti_N$$
  • If there are both independent sources and dependent sources, solve for $$v_{oc}=v_T$$ first, then put a short circuit between the terminals and solve for $$i_{sc}=i_N$$. Recall that $$v_T=R_Ti_N$$
  • If there are only dependent sources, you have to activate the circuit with an external source.