ECE 110/Concept List/S24

Lecture 1 - 1/11 - Course Introduction, Nomenclature

• Circuit terms (Element, Circuit, Path, Branch and Essential Branch, Node and Essential Node, Loop and Mesh).
• Accounting:
  • # of Elements * 2 = total number of voltages and currents that need to be found using brute force method
  • # of Essential Branches = number of possibly-different currents that can be measured
  • # of Meshes = number of independent currents in the circuit (or generally Elements - Nodes + 1 for planar and non-planar circuits)
  • # of Nodes - 1 = number of independent voltage drops in the circuit
• Electrical quantities (charge, current, voltage, power)

Lecture 2 - 1/16 - Electrical Quantities

• Passive Sign Convention and Active Sign Convention and relation to calculating power absorbed and/or power delivered.
• Power conservation
• Kirchhoff's Laws
  • Number of independent KCL equations = nodes-1
  • Number of independent KVL equations = meshes
• Example of how to find $$i$$, $$v$$, and $$p_{\mathrm{abs}}$$ using conservation equations and how to check using extra conservation equations
• $$i$$-$$v$$ relationships of various elements (ideal independent voltage source, ideal independent current source, short circuit, open circuit, switch)
• Resistor symbol (and spring symbol)

Lecture 3 - 1/18 - Equivalents

• Resistance as $$R=\frac{\rho L}{A}$$
• $$i$$-$$v$$ relationship for resistors; resistance [$$\Omega$$] and conductance $$G=1/R$$ $$[S]$$
• $$i$$-$$v$$ for dependent (controlled) sources (VCVS, VCCS, CCVS, CCCS)
• Combining voltage sources in series; ability to move series items and put together
• Combining current sources in parallel; ability to move parallel items and put together
• Equivalent resistances
  • series and parallel
  • Examples/Req

Lecture 4 - 1/23 - Brute Force Method; Delta-Wye; Voltage Division Part 1

• Brute Force method
• Delta-Wye equivalencies (mainly refer to book)
• Voltage Division

Lecture 5 - 1/25 - Voltage Division Part 2, Current Division, and Node Voltage Division Part 1

• Voltage Re-Division
• Current Division and Re-Division
• Basics of NVM

Lecture 6 - 1/30 - Node Voltage Method

• Examples on Canvas
• NVM
  • Labels:
    • Very Lazy: label ground, then make every other node a new unknown. Voltage sources, voltage measurements, and current measurements will provide additional equations.
    • Lazy: label ground, then label any node connected to ground if it has a voltage source or voltage measurement. Make every other node a new unknown. Voltage sources not connected to ground, voltage measurements not connected to ground, and current measurements will provide additional equations.
    • Smart: label ground; once a node gets labeled, if there is a voltage source or a voltage measurement anchored at that node, use the source or measurement to label the other node it is attached to. Current measurements will provide additional equations.
    • Really Smart: same as smart, only also use voltage drops across resistors with current measurements to relate node voltages.

Lecture 7 - 2/1 - Current Methods

• Examples on Canvas
• BCM
  • Labels:
    • Label each (essential) branch current, using as few unknowns as possible by incorporating current source and current measurement labels
• MCM
  • Labels:
    • Label each mesh current, understanding that current sources, current measurements, and voltage measurements will require additional equations.

Lecture 8 - 2/6 - Linearity and Superposition

• Definition of a linear system
• Examples of nonlinear systems and linear systems
  • Nonlinear system examples (additive constants, powers other than 1, trig):

$$\begin{align*} y(t)&=x(t)+1\\ y(t)&=(x(t))^n, n\neq 1\\ y(t)&=\cos(x(t)) \end{align*} $$

• Linear system examples (multiplicative constants, derivatives, integrals):

$$\begin{align*} y(t)&=ax(t)\\ y(t)&=\frac{d^nx(t)}{dt^n}\\ y(t)&=\int x(\tau)~d\tau \end{align*} $$

• Superposition
  • Redraw the circuit as many times as needed to focus on each independent source individually
  • Use combinations of Phm's Law, Voltaeg Division, and Current Division, rather than setting up and solving multiple equations
  • If there are dependent sources, you must keep them activated and solve for measurements each time - this likely means that superposition may not actually make solving things easier.

Lecture 9 - 2/8 - Thévenin and Norton Equivalent Circuits

• Thévenin and Norton Equivalents
• Circuits with independent sources, dependent sources, and resistances can be reduced to a single source and resistance from the perspective of any two nodes
• Equivalents are electrically indistinguishable from one another
• Several ways to solve:
  • If there are only independent sources, turn independent sources off and find $$R_{eq}$$ between terminals of interest to get $$R_{T}$$. Then find $$v_{oc}=v_{T}$$ and recall that $$v_T=R_Ti_N$$
  • If there are both independent sources and dependent sources, solve for $$v_{oc}=v_T$$ first, then put a short circuit between the terminals and solve for $$i_{sc}=i_N$$. Recall that $$v_T=R_Ti_N$$
  • If there are only dependent sources, you have to activate the circuit with an external source.

Lecture 10 - 2/13 - Capacitors and Inductors

• Intro to capacitors and inductors
• Basic physical models
• Basic electrical models
• Energy storage
• Continuity requirements
• Finding circuit equation models
• DCSS equivalents

Lecture 11 - 2/15 - Initial Conditions and Finding Equations

• DCSS equivalents
• Finding values just before and just after circuit changes
  • For $$t=0^+$$, can model inductor as independent current source and capacitor as independent voltage source
• Using Node Voltage Method to get model equations